What P0118 Means
P0118 indicates the engine control module (ECM) has detected a voltage signal from the engine coolant temperature (ECT) sensor that is higher than the expected range for the current operating conditions. The ECT sensor is a thermistor—a resistor that changes resistance with temperature—and the ECM supplies it with a reference voltage (typically 5 volts) and monitors the return signal. As coolant temperature rises, the sensor's resistance decreases and the signal voltage drops. When the ECM sees a signal voltage that remains too high for too long, suggesting an implausibly cold reading (often below -40°F or -40°C equivalent), it sets P0118.
The ECM uses coolant temperature data to adjust fuel delivery, ignition timing, idle speed, and cooling fan operation. An open circuit or failed sensor reporting an unrealistically low temperature can cause the ECM to enrich the fuel mixture excessively, run the fans continuously, and alter other parameters, leading to drivability issues and increased emissions.
Symptoms
Many vehicles show only the check engine light when P0118 is stored. Other common symptoms include:
- Hard starting, especially when the engine is cold
- Rough idle or hesitation during acceleration
- Poor fuel economy due to overly rich fuel mixture
- Black smoke from the exhaust
- Cooling fans running at full speed even when the engine is cold
- Engine may run hotter than normal if the ECM defaults to a failsafe temperature value
In some cases, the ECM substitutes a default coolant temperature value (often around 176°F or 80°C) to keep the engine running, which may mask symptoms until the vehicle is started cold.
Causes, Most Likely First
The most common cause of P0118 is an open circuit in the ECT sensor wiring—a broken wire between the sensor and the ECM. This breaks the signal path and pulls the voltage to the reference level, triggering the high-input fault.
Other causes, ranked by frequency:
- Failed ECT sensor with an internal open circuit
- Corroded, loose, or damaged ECT sensor connector causing intermittent or complete loss of signal
- Damaged wiring harness due to heat, abrasion, or rodent damage
- Short to voltage in the ECT sensor signal wire (less common than an open)
- Failed ECM (rare; usually only after all other causes are ruled out)
Manufacturer-specific variations exist. Some vehicles use a two-wire ECT sensor with a dedicated ground, while others use a single-wire sensor that grounds through the engine block. Consult your vehicle's service information for the exact circuit design and common failure modes.
How to Diagnose P0118
Follow these steps from simplest to most involved. Always confirm specifications in your vehicle's service manual, as sensor resistance values and voltage ranges vary by manufacturer.
-
Read freeze frame data using a scan tool to see the ECT reading and other parameters when the code was set. If the freeze frame shows an ECT reading of -40°F (-40°C) or similar extreme low value, suspect an open circuit.
-
Check live ECT sensor data with the engine cold, then warm. A functioning sensor should show a reading close to ambient temperature when cold (typically 60–100°F or 15–38°C depending on climate) and rise smoothly to around 180–220°F (82–104°C) at operating temperature. If the reading is stuck at an extreme low value, proceed to the next step.
-
Inspect the ECT sensor connector for corrosion, bent pins, moisture, or looseness. Disconnect the connector and examine both the sensor and harness sides. Clean with electrical contact cleaner if needed and ensure a tight fit when reconnected.
-
Test ECT sensor resistance. Disconnect the sensor and measure resistance across its terminals with a multimeter. Compare the reading to the temperature-resistance chart in your service information. As a general reference, many sensors read around 2,000–3,000 ohms at 68°F (20°C) and drop to around 200–300 ohms at 194°F (90°C), but these values vary widely by design. If the sensor reads infinite resistance (open circuit), replace it.
-
Check wiring continuity and resistance. With the sensor disconnected, check continuity from the ECM connector to the sensor harness connector on both the signal and ground wires. There should be low resistance (typically under 5 ohms). Also check for shorts to voltage or ground by measuring voltage on the signal wire with the key on, engine off, and the ECM connector still attached but the sensor disconnected. You should see close to 5 volts if the circuit is intact.
-
Test the ECM signal circuit. If wiring and sensor test good, the fault may lie in the ECM itself. This diagnosis typically warrants a qualified mechanic or specialist with access to advanced diagnostic equipment and wiring diagrams.
Reviewing freeze frame data can reveal whether the fault is present continuously or occurs only under specific conditions, such as key-on before the engine starts.
Is It Safe to Drive With P0118?
Driving with P0118 is generally safe for short distances under moderate conditions, but it carries risks. The ECM may default to a fixed coolant temperature value, which can cause the engine to run rich, foul spark plugs, and increase fuel consumption. In cold weather, the engine may be difficult to start or run poorly until it warms up. In hot weather or under heavy load, the ECM may not activate the cooling fans appropriately, increasing the risk of overheating.
Avoid extended driving if:
- The engine is overheating or the temperature gauge reads higher than normal
- The vehicle stalls, hesitates severely, or exhibits unsafe drivability issues
- You are operating in extreme cold or hot conditions
Address the code promptly to restore proper engine management and avoid potential damage from running too rich or overheating.
Repair Options
DIY: Inspect and clean the ECT sensor connector, check for obvious broken or chafed wiring, and verify the sensor is properly seated. If you have a multimeter and are comfortable with basic electrical testing, measure sensor resistance and compare it to published specifications.
Intermediate: Replace the ECT sensor if resistance testing shows it is out of range or open. Repair or replace damaged wiring if you find breaks, shorts, or excessive resistance. Many ECT sensors are accessible and inexpensive, making replacement straightforward for a home mechanic with basic tools.
Professional: Intermittent faults, wiring harness damage in hard-to-reach areas, and ECM-level diagnosis warrant a qualified mechanic. A shop will have wiring diagrams, specialized test equipment, and the ability to perform pinpoint tests on the ECM and related circuits.
Diagnostic output is a decision-support estimate, not a substitute for professional inspection.
Related Codes
P0117 (Engine Coolant Temperature Sensor Circuit Low Input) is the opposite fault, indicating the ECT signal voltage is too low, typically caused by a short to ground or a sensor reading an implausibly high temperature. P0117 and P0118 often point to the same circuit but different failure modes, so if you see both codes or they alternate, focus on the wiring and connector integrity.
Other codes that may appear alongside P0118 include fuel trim codes if the ECM has been compensating for an incorrect temperature reading, or idle control codes if the default temperature strategy affects idle speed. Addressing P0118 first often clears these secondary codes.