What P0112 Means
P0112 indicates the powertrain control module (PCM) has detected a voltage signal from the intake air temperature (IAT) sensor that is below the expected range. The PCM monitors the IAT sensor continuously to measure the temperature of air entering the engine, using that data to adjust fuel delivery and ignition timing for optimal combustion.
The IAT sensor is a thermistor—a resistor whose resistance changes with temperature. As air temperature increases, resistance decreases, and the voltage signal to the PCM rises. When the PCM sees a voltage lower than the minimum threshold (typically indicating an implausibly cold temperature, often below -40°F or -40°C), it sets P0112. This low voltage usually points to a short circuit in the sensor or wiring rather than an actual extreme cold condition.
Manufacturer-specific definitions and fault thresholds can vary, so always confirm the exact criteria in your vehicle's service information.
Symptoms
Many drivers notice no symptoms beyond the check engine light. When symptoms do occur, they include:
- Check engine light illuminated (malfunction indicator lamp)
- Hard starting, particularly in cold weather
- Rough idle or engine stalling
- Poor fuel economy due to overly rich fuel mixture
- Black smoke from the exhaust
- Hesitation or stumbling during acceleration
Because the PCM may default to a substitute value when the IAT signal is out of range, drivability problems can be mild or absent, especially in moderate ambient temperatures.
Causes, Most Likely First
- Damaged or shorted wiring in the IAT sensor circuit — the most common cause. Wiring can chafe against engine components, melt near hot exhaust parts, or be damaged by rodents.
- Corroded or damaged connector at the IAT sensor — moisture intrusion, oil contamination, or physical damage can create a short or low-resistance path.
- Failed intake air temperature sensor — internal short circuit within the sensor itself.
- Short to ground in the signal wire — anywhere between the sensor and the PCM.
- Powertrain control module fault — rare, but internal PCM damage can cause false low-voltage readings.
On some vehicles the IAT sensor is integrated into the mass airflow sensor, so a fault in that combined unit can also trigger P0112.
How to Diagnose P0112
Follow these steps from simplest to most involved. Diagnostic output is a decision-support estimate, not a substitute for professional inspection.
-
Read freeze-frame data. Check the freeze-frame snapshot to see the IAT reading, engine temperature, and other conditions when the code set. An implausibly low temperature (such as -40°F when ambient is 70°F) confirms the circuit fault.
-
Inspect the IAT sensor and connector. Locate the sensor—often in the intake air duct or integrated into the MAF sensor housing. Look for damaged pins, corrosion, moisture, or oil contamination in the connector. Inspect the wiring for chafing, burns, or rodent damage.
-
Measure IAT sensor resistance. Disconnect the sensor and use a multimeter to measure resistance across its terminals. Compare the reading to the temperature-resistance chart in your vehicle's service information. A reading near zero ohms indicates an internal short.
-
Check signal voltage at the sensor connector. With the key on and engine off, backprobe the signal wire at the sensor connector (sensor still connected). You should see a voltage that corresponds to ambient air temperature. A voltage near zero with the sensor connected suggests a short to ground.
-
Test for shorts to ground. Disconnect the IAT sensor and the PCM connector (or use a breakout box). Measure resistance between the signal wire and ground. Any reading below several thousand ohms indicates a short in the harness.
-
Compare IAT reading to ambient temperature. Use a scan tool or OBD2 app to view live IAT data. Compare it to actual ambient temperature. If the sensor and wiring test good but the reading is still implausible, suspect a PCM issue.
Consult your vehicle's service manual for exact resistance values and voltage specifications, as these vary by manufacturer. If you lack the tools or experience to perform these tests safely, a qualified technician should diagnose the fault.
Is It Safe to Drive With P0112?
You can usually drive short distances with P0112, but it is not advisable for extended use. The engine will likely run rich because the PCM assumes colder air (which is denser) and adds extra fuel. This wastes fuel, may cause rough running, and can foul spark plugs or damage the catalytic converter over time.
Hard starting may leave you stranded, especially in cold weather. If the check engine light is flashing, the engine is misfiring severely—stop driving immediately to avoid catalytic converter damage. If you experience stalling, loss of power, or other driveability issues, have the vehicle diagnosed and repaired promptly.
Repair Options
DIY repairs are straightforward if the fault is in the sensor or connector:
- Clean corrosion from the connector with electrical contact cleaner.
- Repair or replace damaged wiring. Heat-shrink tubing and solder provide a durable fix for chafed or broken wires.
- Replace the IAT sensor if resistance testing confirms it has failed. Sensors are inexpensive and usually require only a screwdriver or small wrench to swap.
Professional diagnosis and repair may be necessary for:
- Intermittent shorts that are difficult to locate.
- Wiring faults deep in the harness or near the PCM.
- PCM faults, which require specialized diagnostic equipment and, in rare cases, module replacement or reprogramming.
After repairs, clear the code and drive the vehicle through a complete drive cycle to confirm the fix. Monitor live data to verify the IAT reading tracks ambient temperature accurately.
Related Codes
- P0113 — Intake Air Temperature Sensor Circuit High Input (opposite condition: voltage too high)
- P0100 — Mass or Volume Air Flow Circuit Malfunction (if IAT is integrated into the MAF sensor)
- P0103 — MAF/VAF Circuit High Input
- P0108 — Manifold Absolute Pressure/Barometric Pressure Circuit High Input
P0112 and P0113 are complementary codes for the same sensor circuit. If you see both, or if they alternate, suspect an intermittent wiring fault or a failing connector.